Product Description
Milwaukee Plastic Blade Guard Attachment
Model Number: 43-54-4010
The Milwaukee 43-54-4010 Plastic Blade Guard Attachment is a genuine OEM accessory designed for use with select Milwaukee angle grinders, including the 2686-20 M18 4-1/2 in. Cut-Off / Grinder, the 2880-20 M18 FUEL 4-1/2 in. / 5 in. Grinder with No-Lock Paddle Switch, and the 2881-20 M18 FUEL 4-1/2 in. / 5 in. Grinder with Slide Switch and Lock-On. The blade guard attachment is a Type 1 cutting wheel guard accessory that snaps onto the existing Type 27 grinding wheel guard on the tool, converting the open-top grinding configuration into a fully enclosed cutting configuration in seconds without the need for tools or hardware swaps. When the operator switches from grinding wheels to abrasive cutting wheels, diamond blades, or cut-off wheels, the additional plastic guard panel encloses the upper portion of the wheel that the standard Type 27 guard leaves exposed, providing the wraparound protection required for safe cut-off work.
Type 1 and Type 27 wheel configurations have very different guard requirements under ANSI safety standards. Type 27 grinding wheels (depressed-center grinding discs and flap discs) work with an open-top guard that allows the operator to grind on the face of the wheel. Type 1 cutting wheels (cut-off wheels, abrasive blades, and diamond blades) are designed to cut on the edge of the wheel and require a fully enclosed guard that wraps around the upper half of the wheel to contain fragments in the rare event of a wheel-burst incident. The 43-54-4010 attachment converts the standard Milwaukee Type 27 grinder guard into a Type 1 configuration by clipping over the existing guard, eliminating the need to remove and swap a separate complete guard assembly between grinding and cutting jobs. This makes the tool faster to reconfigure on the jobsite and reduces the chance of an operator running a Type 1 cutting wheel without proper guard coverage.
Manufactured to Milwaukee's exact factory tolerances, this OEM attachment provides correct fitment to the Milwaukee Type 27 grinder guard on compatible 5 in. angle grinders and full Type 1 wheel coverage when properly installed. Always operate Milwaukee angle grinders with the correct guard configuration for the wheel type being used, follow the wheel manufacturer's RPM ratings and orientation guidelines, and inspect both the primary guard and the blade guard attachment for cracks, breakage, or impact damage before each use. A damaged or missing blade guard attachment must be replaced before running cutting wheels on the tool. Verify your tool's catalog number and serial number against the official Milwaukee parts diagram or operator manual before ordering to confirm the 43-54-4010 is the correct accessory for your specific grinder.
Features
- Genuine Milwaukee OEM accessory, direct factory part for the 43-54-4010 reference
- Compatible with the Milwaukee 2686-20, 2880-20, and 2881-20 angle grinders
- Type 1 cutting wheel guard attachment for cut-off wheels, abrasive blades, and diamond blades
- Clips onto the standard Type 27 grinder guard, no tools or hardware swap required
- Converts open-top grinding guard into fully enclosed cutting guard in seconds
- Eliminates the need to remove and swap a complete guard assembly between grinding and cutting jobs
- Provides correct wraparound coverage for Type 1 cutting wheel applications
- Required for safe operation when running cutting wheels on Milwaukee 5 in. angle grinders
- Direct-fit accessory, no modification required for installation
- Manufactured to Milwaukee factory tolerances for clean fitment to the existing tool guard
Specifications
- Manufacturer: Milwaukee Tool
- Part Number: 43-54-4010
- Official Description: Plastic Guard Attachment
- Component Type: Clip-On Type 1 Cutting Wheel Guard Accessory
- Material: Plastic construction
- Wheel Compatibility: 5 in. (125 mm) Type 1 cutting wheels
- Confirmed Compatible Tools: 2686-20 M18 4-1/2 in. Cut-Off / Grinder, 2880-20 M18 FUEL 4-1/2 in. / 5 in. Grinder with No-Lock Paddle Switch, 2881-20 M18 FUEL 4-1/2 in. / 5 in. Grinder with Slide Switch
- Quantity: Sold individually, 1 attachment per order
- Part Type: OEM Accessory
Includes
- (1) Milwaukee 43-54-4010 Plastic Blade Guard Attachment
- Note: Primary Type 27 grinder guard is NOT included. This attachment clips onto the existing tool guard
- Note: Cutting wheels, cut-off wheels, abrasive blades, and diamond blades are NOT included and sold separately
- Note: Mounting hardware is not required, the attachment is a clip-on design
- Note: This attachment is for Type 1 cutting wheel applications only. Type 27 grinding operations use the standard tool guard without this attachment
- Note: This attachment is specific to Milwaukee 5 in. angle grinders. It is NOT compatible with Milwaukee 6 in., 7 in., or 9 in. large-format grinders, which use larger guard systems with their own dedicated cutting wheel attachments
- Note: Verify your tool's catalog number and serial number against the official Milwaukee parts diagram or operator manual before ordering
