Product Description
**Milwaukee parts change not only by model# but also by serial number. Milwaukee's site lets you look up your tool's parts diagram. Enter Cat# and Select Service Parts. Also match Serial Number.
Milwaukee Drawer Slide Kit (Set of 2)
Model Number: 14-46-1662
The Milwaukee 14-46-1662 is a genuine OEM Drawer Slide Kit, a set of two, for the Milwaukee 56 in. High Capacity Steel Storage chest and cabinet. The kit is the replacement pair of full-extension, soft-close drawer slides that one drawer rides on, with an inner and an outer slide per side, so the drawer rolls out fully, carries its rated load, and closes smoothly. These are the 150 lb soft-close slides the 56 in. series is built around, and they take the weight of a loaded drawer opened and closed thousands of times. Because a slide carries that load on ball bearings in a steel channel, it can wear, bind, bend, or lose its smooth travel over the cabinet's life, at which point the drawer drags, sags, or will not close square. Replacing the slides with the genuine Milwaukee OEM kit restores full, smooth, load-rated drawer travel, where an off-spec slide may not fit the cabinet's mounting or carry the load.
This kit is identified as the Drawer Slide Kit (Set of 2), Figure 29, on the Milwaukee service parts list for the 56 in. High Capacity Steel Storage chest and cabinet (catalog numbers 48-22-8556, 48-22-8557, and 48-22-8558), bulletin 54-49-8555. It supplies two outer drawer slides, two inner drawer slides, and the 5/32 in. pop rivets to mount them, enough to service one drawer. Milwaukee's steel storage uses different slide kits for different cabinet sizes, so the 56 in. series takes this kit (14-46-1662), while the 30, 36, 40, and 41 in. cabinets use a different kit, so match the kit to your cabinet. The slides install by drilling out the old 5/32 in. rivets and setting the new slides with a rivet gun. Because Milwaukee specifies service parts by catalog and serial number, verify your catalog and serial number against the official Milwaukee service parts diagram before ordering.
Features
- Genuine Milwaukee OEM drawer slide kit (set of 2)
- For the Milwaukee 56 in. High Capacity Steel Storage chest and cabinet
- Replaces the drawer slides one drawer rides on (inner and outer per side)
- Full-extension, soft-close, 150 lb rated slides
- Supplies two outer slides, two inner slides, and the pop rivets to mount them
- Enough to service one drawer
- Figure 29 on the service parts diagram (bulletin 54-49-8555)
- Fits the 56 in. series (48-22-8556, 48-22-8557, 48-22-8558)
- Different from the slide kits for the 30, 36, 40, and 41 in. cabinets
- Installs by drilling out the old 5/32 in. rivets and setting the new slides
- Restores full, smooth, load-rated drawer travel
- Replace if a drawer drags, sags, binds, or will not close square
Specifications
- Manufacturer: Milwaukee Tool
- Part Number: 14-46-1662
- Official Description: Drawer Slide Kit (Set of 2)
- Component Type: Steel storage drawer slide service kit
- Slide Type: Full-extension, soft-close (150 lb rated on the 56 in. series)
- Primary Fitment: Milwaukee 56 in. High Capacity Steel Storage (48-22-8556, 48-22-8557, 48-22-8558)
- Parts Diagram Position: Figure 29 (bulletin 54-49-8555)
- Quantity: Sold as a kit (set of 2 slides for one drawer)
- Part Type: Genuine Milwaukee OEM Replacement Part
Includes
- (2) Outer Drawer Slides
- (2) Inner Drawer Slides
- 5/32 in. Pop Rivets (installation hardware)
The kit services one drawer, so order one kit per drawer being replaced. This kit is for the 56 in. series, not the 30, 36, 40, or 41 in. cabinets (which use a different slide kit), so match the kit to your cabinet. Always verify by catalog and serial number using Milwaukee's online parts lookup before ordering.
